ISU_MAN_TRANS_WASTE_OBJECTS SAP Function module - INTERNAL: Transport Connection Misc. Transactions Waste

ISU_MAN_TRANS_WASTE_OBJECTS is a standard SAP function module available within R/3 SAP systems depending on your version and release level. Below is the pattern details for this FM showing its interface including any import and export parameters, exceptions etc as well as any documentation contributions (Comments) specific to the object.

See here to view full function module documentation and code listing, simply by entering the name ISU_MAN_TRANS_WASTE_OBJECTS into the relevant SAP transaction such as SE37 or SE80.

Associated Function Group: EEWA_TRANSPORT
Released Date: Not Released
Processing type: Normal fucntion module

Pattern for FM ISU_MAN_TRANS_WASTE_OBJECTS - ISU MAN TRANS WASTE OBJECTS

CALL FUNCTION 'ISU_MAN_TRANS_WASTE_OBJECTS' "INTERNAL: Transport Connection Misc. Transactions Waste
  EXPORTING
    x_tab =                     " tabname       Table Name
    x_sobj =                    " e071-obj_name
*   x_texttab =                 " e071k-objname  Table Name
*   x_keytab_bill =             " isuwa_keytab_aat  Table of Key Fields for Waste Billing Category
*   x_keytab_robtyp =           " isuwa_irobtyp  Table Category for Structure ISUWA_ROBTYP
*   x_keytab_cal =              " isuwa_iecal   ISUWA_ECAL
*   x_keytab_faktor =           " t_ewa_faktor  Table Type of Waste Billing Factor
*   x_spras =                   " sy-langu      Language Key
  IMPORTING
    y_ok =                      " regen-kennzx
  EXCEPTIONS
    GENERAL_FAULT = 1           "               General Error
    KORRNR_ERROR = 2            "
    APPEND_ERROR = 3            "
    .  "  ISU_MAN_TRANS_WASTE_OBJECTS

ABAP code example for Function Module ISU_MAN_TRANS_WASTE_OBJECTS

The ABAP code below is a full code listing to execute function module ISU_MAN_TRANS_WASTE_OBJECTS including all data declarations. The code uses the latest in-line data DECLARATION SYNTAX but I have included an ABAP code snippet at the end to show how declarations would look using the original method of declaring data variables up front. This will allow you to compare and fully understand the new inline method. Please note some of the newer syntax such as the @DATA is not available until a later 4.70 service pack (SP8).

DATA:
ld_y_ok  
 
 TYPE REGEN-KENNZX
.


DATA(ld_x_tab) = 'Check type of data required'.
 

SELECT single OBJ_NAME 
  FROM E071 
  INTO @DATA(ld_x_sobj).

 

SELECT single OBJNAME 
  FROM E071K 
  INTO @DATA(ld_x_texttab).


DATA(ld_x_keytab_bill) = 'Check type of data required'.

DATA(ld_x_keytab_robtyp) = 'Check type of data required'.

DATA(ld_x_keytab_cal) = 'Check type of data required'.

DATA(ld_x_keytab_faktor) = 'Check type of data required'.

DATA(ld_x_spras) = 'Check type of data required'.
.

CALL FUNCTION 'ISU_MAN_TRANS_WASTE_OBJECTS'
  EXPORTING
    x_tab =                      ld_x_tab
    x_sobj =                     ld_x_sobj
*   x_texttab =                  ld_x_texttab
*   x_keytab_bill =              ld_x_keytab_bill
*   x_keytab_robtyp =            ld_x_keytab_robtyp
*   x_keytab_cal =               ld_x_keytab_cal
*   x_keytab_faktor =            ld_x_keytab_faktor
*   x_spras =                    ld_x_spras
  IMPORTING
    y_ok =                       ld_y_ok
  EXCEPTIONS
    GENERAL_FAULT =              1
    KORRNR_ERROR =               2
    APPEND_ERROR =               3
    .  "  ISU_MAN_TRANS_WASTE_OBJECTS

IF SY-SUBRC EQ 0.
  "All OK
ELSEIF SY-SUBRC EQ 1. "Exception
  "Add code for exception here
ELSEIF SY-SUBRC EQ 2. "Exception
  "Add code for exception here
ELSEIF SY-SUBRC EQ 3. "Exception
  "Add code for exception here
ENDIF.

ABAP code to compare 7.40 inline data declaration with original syntax

The below ABAP code uses the older none in-line data declarations. This allows you to see the coding differences/benefits of the later inline syntax. It may also be useful if you are using an older version of SAP as some of the newer syntax above, such as the @DATA is not available until 4.70 EHP 8.

DATA:

ld_y_ok
 
 TYPE REGEN-KENNZX ,
ld_x_tab
 
 TYPE TABNAME ,
ld_x_sobj
 
 TYPE E071-OBJ_NAME ,
ld_x_texttab
 
 TYPE E071K-OBJNAME ,
ld_x_keytab_bill
 
 TYPE ISUWA_KEYTAB_AAT ,
ld_x_keytab_robtyp
 
 TYPE ISUWA_IROBTYP ,
ld_x_keytab_cal
 
 TYPE ISUWA_IECAL ,
ld_x_keytab_faktor
 
 TYPE T_EWA_FAKTOR ,
ld_x_spras
 
 TYPE SY-LANGU .


ld_x_tab = 'Check type of data required'.

SELECT single OBJ_NAME 
  FROM E071 
  INTO ld_x_sobj.


SELECT single OBJNAME 
  FROM E071K 
  INTO ld_x_texttab.

ld_x_keytab_bill = 'Check type of data required'.
ld_x_keytab_robtyp = 'Check type of data required'.
ld_x_keytab_cal = 'Check type of data required'.
ld_x_keytab_faktor = 'Check type of data required'.
ld_x_spras = 'Check type of data required'.